China drift beads materials market development research report
Coal-fired power plants increase grinding coal into coal, injection power boiler furnace, let its suspension combustion. Coal combustible component (c) and organic matter most of the burning, and clay is not combustible component (silicon, aluminum, iron, magnesium, etc.) in the chamber of a stove or furnace temperatures of 1300 degrees Celsius began to melt, forming quartz glass and mullite porous symbionts, the hole is filled with gas. When the temperature reached 1400 degrees Celsius, the molten body particle surface tension can be dropped to the lowest, can make the surface edges and get rid of the surface energy and contraction, molten particles will be floating roll forming sphere. At this point, the porous body of gases such as CO, CO 2, N2, H 2 wrapped in a ball. When the temperature continued to rise, gas expansion inside the glass ball, and make a sphere increases, crust thinning, the formation of hollow sphere. Empty sphere of leaving furnace, rapidly cooling after, became the hard shell of glass beads. These glass beads, due to the wall thickness and weight is different, can be divided into two classes. Which one kind is thin-wall hollow spheres (one over ten of the wall thickness to diameter), because can float water, is called a "floating bead". Another kind is the wall thickness of hollow spheres (a third of the wall thickness to diameter) and solid sphere, because of the heavy and sink to the bottom, therefore calls "sinking beads: high iron content are called" magnetic beads ". I mean drift beads is first class.
Cenosphere: hollow inorganic nonmetal glass spheres;
Drift beads: (can float on the surface of the water, the proportion of less than 1, one over ten of the wall thickness to diameter);
Sinking beads: (drowned in the water, the proportion of greater than 1, the third part of the wall thickness to diameter).
After several research, we consulted a lot of experts, think it difficult to drift beads classification points, or domestic now there is no clear classification. So in order to better define drift beads, we according to the classification of fly ash to drift beads.
Fly ash is a kind of complex fine dispersed solid matter, it is mainly composed of silicon oxide (aluminum), glass ball, according to its grain structure type can be divided into beads of two kinds of particles and slag particles. Bead particles including drift beads (often called cenosphere), hollow sinking beads, dense sinking beads, magnetic beads four varieties; Slag particles mainly includes the cavernous glass bead, granular, etc. As a result of the various power plants burning coal, coal quality and boiler operation state, dust removal of fly ash and so the morphology, structure, physical and chemical properties as well as the number of all kinds of beads will form also have differences.
Orders to record
The first chapter China drift beads material market overview
The first section product market definition
Product categories in the second quarter
The third quarter the market characteristics
One, the life cycle
Second, the production of technological change and product innovation
The second chapter drift beads materials market development situation
The first section in the international market development situation
A, analysis of the present distribution of our products on the international application
Second, the product is mainly applications of countries and regions
In the second quarter, 2009 years ago, three years China drift beads material market analysis
First, the current situation of the development of the domestic market
Second, the overall market size and growth of our country
Chapter 3, 2009 years ago China drift beads materials market investigation and analysis of supply and demand
In the first quarter demand analysis
A regional structure analysis, demand
Second, the product structure analysis
Third, analysis of customer surveys
Supply analysis in the second quarter
A, output and its growth analysis
Second, the production area structure analysis
The third section of supply and demand balance analysis
The fourth section upstream raw material market analysis
The fourth chapter domestic import and export of drift beads materials analysis
In the first quarter exports and growth in our country
The second section mainly exported to overseas market distribution
In the third quarter import analysis
Chapter 5, 2009 years ago, three years China drift beads material market competition and enterprise competitiveness evaluation
The first section analysis on domestic enterprise and brand
The second section analysis on the competitive landscape
In the third quarter product market share analysis
The fourth main enterprise competitiveness evaluation
A, product competitiveness
Second, the price is competitive
Three, channel competitiveness
Four, marketing competitiveness
The sixth chapter, domestic market products, price analysis
The first section analysis of characteristics of the price
The second section mainly brand product price analysis
The third section of the competitors pricing strategy
Chapter 7, 2010 years ago, three years of drift beads market upstream and downstream market investigation and analysis
The first section of raw materials market
The upstream raw materials, floating beads
Second, the domestic production
Three, raw material prices
Fourth, industrial policy
Consumer market in the second quarter
A, drift beads consumer market
Secondly, structural change in the drift beads consumer market trend
Three, floating bead downstream market policies
Chapter viii. Domestic main production enterprise profitability analysis
The first section of hebei xingtai guangzhou hongtai drift beads co., LTD
A, enterprise introduction
Second, the product composition
Three, production statistics
Fourth, the SWOT analysis of an enterprise
City of luoyang macro light bleaching bead factory in hebei province in the second quarter
A, enterprise introduction
Second, the product composition
Three, production statistics
Fourth, the SWOT analysis of an enterprise
In the third quarter Anhui huainan RongQingPiao bead processing co., LTD
A, enterprise introduction
Second, the product composition
Three, production statistics
Chapter 9 key regional market consumption survey
The first section of Beijing
A, the structure of the product brand
Second, the consumer channels
Three, price trends
Four, the application and type of industry
Shanghai in the second quarter
A, the structure of the product brand
Second, the consumer channels
Three, price trends
Four, the application and type of industry
The third section of henan province
A, the structure of the product brand
Second, the consumer channels
Three, price trends
Four, the application and type of industry
The fourth quarter, liaoning
A, the structure of the product brand
Second, the consumer channels
Three, price trends
Four, the application and type of industry
Section 5 shandong
A, the structure of the product brand
Second, the consumer channels
Three, price trends
Four, the application and type of industry
Chapter 10 influence drift beads materials 2010-2013 China market development factors
In the first quarter
In the second quarter
Chapter 11, 2010-2010, drift beads materials market development prospect forecast
The first section in the international market development prospect forecast
The second section drift beads material the prospect of market allocation of resources in our country
In the third quarter market space analysis
First, the user needs analysis
Second, analysis of market supply
The fourth market for medium and long-term forecast
A, 2010-2013, economic growth and the product sales forecast
Second, the product output forecast in 2010-2013
Section 5, 2010-2013 China drift beads material market trend analysis
A, product development trend
Second, the price change trend
Three, channel development trend
Fourth, the user demand trends
Chapter 12 This topic report's main conclusions and policy recommendations
The first section of this report main conclusions and views
In the second quarter of the vertical and horizontal sole strategy recommendations
1. The macro strategy point of view
2. The medium industry point of view
3. The micro enterprise point of view
Chapter 13 China's floating bead industry project investment risk and feasibility analysis
The first section product technology application considerations
Project investment matters needing attention in the second quarter
The third section product production and development
Fourth quarter sales note
Section 5 basic conclusion industry analysis
Section 6 basic framework of the investment project feasibility study report
The third chapter China drift beads materials market investigation and analysis of supply and demand
In the first quarter demand analysis
A regional structure analysis, demand
Figure 3-1 in 2006-2009 domestic drift beads sales and growth
Source: China building materials association;
Table 3-1, 2007-2010, domestic demand for drift beads regional structure
The northeast north east China central China south China southwest northwest
7.69% 29.14% 35.26% 10.24% 29.14% 4.36% 7.69% in 2007
7.95% 28.91% 34.25% 11.47% 28.91% 4.71% 7.95% in 2008
8.14% 28.45% 35.17% 10.14% 28.45% 4.90% 8.14% in 2009
2010 1-8.45% 27.95% 34.28% 10.47% 27.95% 5.25% 34.28% in May
Source: China building materials association;
Because our country floating bead is mainly used as refractory, and east China and north China is the rapid development of the real estate market in China area. Can be seen from the chart, the demand of the drift beads is relatively obvious regional structure, the east China area and the dosage of the largest in north China, were accounted for about 45% of the demand scale. Followed by the central and southern China, both share of about 10%, respectively. Less dosage more central and southern areas in northeast China, but showed a trend of increasing, increased from 7.69% in 2007 to 8.45% in May 2010 years ago. Southwest and northwest dosage is less.
The figure of 2007-2010 average price drift beads
Figure 3-2 domestic bleaching bead prices in 2006-2010
Source: China building materials association;
Second, the product structure analysis
Table 3-2 demand product structure in 2007-2010
Less than 20 mesh 20 mesh, 30 mesh 40 mesh is greater than 40 mesh
3.47% 51.24% 25.84% 3.47% 3.47% in 2007
3.28% 48.91% 26.28% 3.28% 3.28% in 2008
2.65% 48.25% 27.39% 2.65% 2.65% in 2009
In 2010, 1-2.87% 47.92% 27.19% 19.58% 47.92% in May
Source: China building materials association;
Through investigation and research in our country's demand for drift beads are mainly concentrated in 20, 30 and 40, 20, 30, 40 mesh is mainly used in refractory materials, construction, etc. Less than 20 mesh less and more than 30 purpose. Can be seen from the chart, 20, 30 and 40 purpose drift beads demand 88.92% in 2007. With the expansion of other types of application, 20, 30 and 40 purpose drift beads showed a trend of slight cut demand, 2010 years ago in May was 86.52%.
Third, analysis of customer surveys
(1) the customer behavior analysis
The oil industry downstream enterprise customers usually take purchasing way. Procurement procedures carried out in accordance with the quality management system strictly, by the company procurement department under the state council in conjunction with the technical department, after investigation and review to determine the qualified supplier quality management department, temporary and special purchasing by bidding or purchasing department by the company after several more choose high quality purchasing.
Oil industry business enterprise for a long time has established a relatively complete supply chain, with reference to foreign advanced enterprise supplier management mode, by the purchasing department to implement effective supplier selection, evaluation and management, and in conjunction with the finance department and quality department, implements the effective control of purchasing cost and purchasing quality, with raw materials suppliers to establish a good long-term cooperative relationship.
(2) analysis of customer satisfaction surveys
Table 3-3 drift beads customer satisfaction survey
Project satisfaction
Quality 95.78%
Delivery time by 91.25%
Delivery point 92.69%
Purchase way by 97.28%
Product packaging by 95.39%
Source: Beijing China through research and consulting co., LTD
(3) the customer purchasing and channel survey analysis
Drift beads enterprise mostly adopts the direct selling method in the domestic sales, product directly to the downstream enterprise configuration. Drift beads enterprise according to the requirement of the hosts, develop products, after verification by general travel through the way such as bidding and negotiation, and customers to establish business relationship. Usually early in this year's sales framework agreement, years according to the specific business need to agree to trade.
Figure 3-3 downstream demand enterprises procurement mode of decision-making of drift beads
Source: Beijing China through research and consulting co., LTD
Supply analysis in the second quarter
A, output and its growth analysis
In 2005 China's production of cenosphere breakthrough 30 million tons, 32.47 million tons by 2007. Since 2008, as the financial crisis causes cenosphere field affected downstream demand, makes the cenosphere production growth is slow, appear even negative growth. Cenosphere in China 2010 years ago may yield a record low, growth fell by 4.73%, yield is 14.3659 million tons only.
Figure 3-4 cenosphere yield and growth in 2005-2010
Source: China building materials association;
Figure 3-5 drift beads production and growth in 2006-2009
Source: China building materials association;
Second, the production area structure analysis
Through investigation we learned that, drift beads of production in China are mainly concentrated in hebei, henan, shanxi, liaoning and anhui provinces, this basically is China's thermal power plants is centered largely in the above areas. The five provinces of drift beads production were occupied more than 50% of the total national output.
Table 3-4 cenosphere production regional structure (the origin production) top five
Unit ten thousand tons
Hebei, shanxi, henan, liaoning province anhui total ratio (%)
412.23 377.98 365.98 412.23 287.98 377.98 53.72% in 2007
400.78 369.87 349.57 400.78 281.47 369.87 54.80% in 2008
387.38 358.23 328.45 387.38 271.27 358.23 53.75% in 2009
In the first five months of 2010 172.87 152.78 148.37 143.68 132.92 750.62 52.27%
Source: China building materials association;
Table 3-5 drift beads production regional structure (the origin production) top five
Hebei, shanxi, henan, liaoning province anhui total ratio (%)
40.14 37.17 36.73 31.29 37.17 174 45.33% in 2007
39.71 36.94 34.17 39.71 26.85 36.94 44.42% in 2008
39.97 and 35.91 30.91 27.91 35.91 44.68% in 2009
In the first five months of 2010 16.17 18.41 17.19 14.28 13.92 79.97 48.68%
Source: China building materials association;
Table 3-6 drift beads product structure (origin production before 5)
Less than 20 mesh 20 mesh, 30 mesh 40 mesh is greater than 40 mesh
10.24 179.89 88.97 72.42 179.89 in 2007
9.42 172.58 85.35 73.83 172.58 in 2008
8.69 167.67 84.46 79.77 167.67 in 2009
In 2010, 1-3.64 70.84 35.75 35.94 70.84 in May
Source: China building materials association;
The third section of supply and demand balance analysis
Drift beads in China market after years of development, now has developed to the mature stage, has realized the basic balance of production and sales. Can be seen from the chart, at present, the supply and demand of drift beads at roughly balanced state, overall supply slightly bigger than the demand, in line with the basic characteristics of mature stage industry.
Figure 3-5, 2006-2010 China cenosphere supply and demand structure
Source: China building materials association;
Figure 3-6, 2006-2010 China drift beads of supply and demand structure
Source: China building materials association;
The fourth section upstream raw material market analysis
First five months of 2010 China's coal industry running in good condition. The raw coal production 1.305 billion tons, up 20.62%, year-on-year growth increased by 13.61%. Power plant coal deposit growth, port coal rise. By the southern water and electricity supply, thermal power demand factors, power plant coal rise. By the end of may, the national unified dispatch power plant coal 49.57 million tons, 5.16 million tons more than the end of last month, the average available for 16 days. On May 31st, the qinhuangdao port coal stockpiles climbed to 6.122 million tons, more than on May 3, 1.47 million tons, ended down for six weeks. Coal prices steady growth. On May 31, qinhuangdao 5500 calories in shanxi optimal mix coal price 755 yuan/ton, 30 yuan/ton increase from the end of last month. According to customs statistics, coal export 8.87 million tons, down 15.8%. Import 57.99 million tons, increase 1.55 times.
In the second half of 2010, China's coal supply although the macroeconomic, the readjustment of the small coal mine, transportation capacity, large coal base construction, and many other factors, slowing growth in the short term, but in the long run, will continue to maintain rapid growth. The 12th five-year plan will be mergers and reorganization of coal as important content. Coal enterprises from the current 11000 to 4000, in 7000. At the end of the "twelfth five-year", will form 6 ~ 8 large-scale coal enterprise group, with annual capacity of 50 million tons to 100 million tons of enterprises amounted to more than 10, oversize coal enterprise production accounts for more than half of total domestic production, coal resources will further focus.
Shanxi, henan, shandong and other places to integrate small coal mines. Small coal mine closure consolidation strength will increase, reduce capacity. Coal mines in China are divided into state-owned coal mine, the state-owned key coal mines and the villages and towns coal mine. State-owned key coal mines in recent years, local state-owned coal mines and the villages and towns coal mine coal production in China accounted for 50%, 15%, 35% of the total. Look from the coal incremental, mainly from state-owned key coal mines and the villages and towns coal mine, 43% and 48% respectively. If the coal demand relative to supply shortage, small coal mine closure consolidation strength will increase, steady progress of resources integration, and production capacity will be reduced. Shanxi provincial government will close objects below mine from 300000 tons to 300000 tons of mine below. Integration of small coal mines of Shanxi Province, is a kind of behavior is dominated by the government - the government designated merger and the main body, specify each merger range, of the specified resource price; Purpose is to form a large mine large groups do new system.
Integration of large groups of coal production in Shanxi Province before accounted for only 51.3% of the total coal production in the province. Hope that through the integration of coal resources in Shanxi Province, by 2011 large group coal production accounted for more than 75% of the province.
Shanxi provincial government decision, according to the state of Shanxi Province, jinzhong, JinDong overall planning of the three coal bases, speed up the construction of coal, electricity, road, port, the sailing for the integration of Shanxi Province steam coal base, coal - coke - electricity - into an organic whole of jinzhong base of coking coal and coal, electricity, gas, into an organic whole JinDong anthracite base. Actively cultivate the datong coal mine, shanxi coking coal, flat: coal, yangquan coal, LuAn mining, jincheng coal, shanxi coal sales, and other enterprises to become three YiDunJi and four 5000 tons of large coal enterprise groups. Practice, according to a mining area as much as possible by the development of a main body, a principal can develop multiple mining area ", the principle of reasonable enterprise merger and reorganization body.
With the development of the market, combined with advanced technology and equipment of fly ash (T160 ladder-shaped production meet the national standard requirements of fly ash) and fly ash are promising in 2010.
Standard of fly ash in 2010: national standard level: the high quality of fly ash and high efficiency water reducing agent composite technology in the production of high grade concrete in modern concrete technology is developing rapidly in the country; National standard level 2: high quality especially suitable for the preparation of fly ash pumping concrete, mass concrete, the permeability of concrete structure, sulfate resistance of concrete and soft water erosion resistance and underground, underwater engineering concrete, concrete grouting concrete and RCC; National standard level 3: fly ash concrete has good workability, pumpability and finishing, impact resistant ability improves, frost resistance enhancement, etc.
Fly ash market prospect analysis:
(1) the application of fly ash in cement and concrete engineering: after grinding machining of fly ash instead of clay raw material to produce cement by adding suitable amount of plaster of fly ash and Portland cement clinker grinding fine hard gelled material made of water, industrial use of fly ash cement ingredients can use of them not burning charcoal; The fly ash cement mixed material; Production of low temperature synthesis of fly ash cement, the production principle is first batch steam curing generate natural gas hydrates, and then by the dehydration and low temperature solid phase reaction to form cement minerals; Made of fly ash cement clinker, including pure fly ash cement, lime fly ash cement and lime fly ash cement is to dry fly ash mixed with 10% - 30% of lime or lime hydrate and a small amount of gypsum mixed grinding, or mill respectively after mixing the water rigid gelled material made of; Fly ash mortar or concrete admixture, adding fly ash to replace partial cement in concrete or fine aggregate, can not only reduce cost, but also can improve the workability of concrete, improve impervious, carbamate, sulfate resistance and chemical corrosion resistance, reduce the hydration heat, improving the high temperature resistant performance of concrete, reduce particle separation and drainage phenomenon, reduce the shrinkage and cracking of concrete, and inhibition of stray current corrosion of steel bar in concrete.
(2) the application of the fly ash in building products: steamed brick of fly ash, fly ash in power plants (T160 trapezoidal after grinding) and lime (high pressure grinding machining) or other alkaline exciting agent as the main raw material, also can be mixed with the right amount of gypsum, and adding a certain amount of coal cinder or water quenching slag aggregates, such as processed, stirring, digestion, grinding wheel, after pressing forming, atmospheric or high pressure steam curing and formed a kind of wall materials; Fly ash sintered brick with fly ash, clay and other industrial waste as raw materials, the raw material, mixing, molding, drying, pei fire bricks into; Autoclaved production foam insulation brick of fly ash, fly ash as the main raw material, adding a certain amount of lime and foaming agent, after ingredients, mixing, injection molding and burning autoclaved and become a new type of insulating brick; Silicate blocks of fly ash, fly ash, lime and gypsum as gelled material, coal cinder, blast furnace slag as aggregate, adding water stirring, vibration moulding, steam curing of wall materials; Fly ash aerated concrete, fly ash as raw material, add lime, cement, gypsum, aluminum powder, and add water mixing slurry, injection mold pipe and become a kind of porous lightweight construction materials; Lytag, fly ash as the main raw material, mixed with a small amount of adhesive and solid fuels, by mixing, into a ball, high temperature burning system of a kind of artificial lightweight aggregate; Fly ash lightweight heat insulation brick, is to use fly ash, burnt stone, soft soil and wood chips of ingredients, heat preservation with high efficiency, high refractoriness, small thermal conductivity, can reduce the wall thickness, shorten the sintering time and lower fuel consumption and higher thermal efficiency, reduce cost.
(3) fly ash (T160 trapezoidal milling machining process) for agricultural fertilizer and soil conditioner: fly ash has good physical and chemical properties, can be widely used in heavy clay, raw soil, acidic soil and saline soils, make up for the defect of their acid thin plate, the fly ash contains a large amount of citrate acid soluble silicon calcium magnesium phosphate crops such as the necessary nutrition elements, it can make agricultural fertilizer use.
(4) the recovery of industrial raw materials, recovery of coal resources, and using the flotation process in the coal fly ash mortar water in flotation reagents, and then USES the air flotation technology, make the coal particle adhesion in bubble buoyancy and ash separation; Fly ash contains metals recycling Fe2O3, Al2O3, and a large number of rare metal; Sorting cenosphere, cenosphere with small mass, high strength, high temperature resistance and good insulation, can be used for plastic ideal filler, used for lightweight refractory and efficient heat preservation material, used in the petroleum chemical industry, used in military field, brake tanks.
(5) for environmental protection material: can produce molecular sieve, using fly ash flocculants and adsorption materials such as environmental protection material; Fly ash (high pressure mill) can also be used for fluoride wastewater treatment examples, electroplating waste water containing heavy metal wastewater and oily wastewater, the fly ash contained of Al2O3, CaO, such as active component, with production of fluoride complexes or have flocculation of colloid on fluorine ion, also contains zeolites, mullite, granular and silica gel, etc., with inorganic ion exchange and adsorption bleaching features.